iC dimensions are shown: inch (mm) specifications and dimensions subject to change www.ck-components.com i slide ts series tiny slide switches features/benefits ? reliable contact design ensures long electrical life ? ratings up to 3 amps ? epoxy terminal-seal compatible with bottom wash cleaning ? rohs compliant typical applications ? test & measurement equipment ? computers & peripherals ? t elecommunications & networking equipment specifications contact rating: b contact material: 0.4 va max. @ 20 v ac or dc max. q contact material (ts01 model): 3 amps @ 120 v ac or 28 v dc; (ts02, ts03 models): 1 amp @ 120 v ac or 28 v dc. see page i-10 for additional ratings. electrical life: ts01 models: 60,000 make-and-break cycles at full load. ts02, ts03 models: 30,000 cycles. contact resistance: below 20 m typ. initial @ 2-4 v dc, 100 ma, for both silver and gold plated contacts. insula tion resistance: 10 9 min. dielectric strength: 1,000 vrms min. @ sea level. opera ting temperature: C0?oto 85? solderability : per mil-std-202f method 208d, or eia rs-186e method 9 (1 hour steam aging). materials case: glass filled nylon 4/6, flame retardant, heat stabilized. actuator: nylon, black standard. housing: stainless steel or stainless steel, nickel plated. end contacts: b contact material: copper alloy, with gold plate over nickel plate. q contact material: coin silver, silver plated. see page i-10 for additional contact materials. center contact & all terminals: b contact material: copper alloy , with gold plate over nickel plate. q contact material: copper alloy, silver plated. see page i-10 for additional contact materials. terminal seal: epoxy. refer to soldering and cleaning in technical data chapter. note: any models supplied with q, b, g, p, s or r contact material are rohs compliant. note: specifications and materials listed above ar e for switches with standard options. for information on specific and custom switches, consult customer service center. build-a-switch t o or der , simply select desir ed option fr om each category and place in the appr opriate box. a vailable options are shown and described on pages iC and i?C. for additional options not shown in catalog, consult customer service center. all models have epoxy terminal seal and are compatible with all ottom--ash?cb cleaning methods. switch function ts01 spdt on-none-on ts02 spst off-none-on ts03 spdt on-off-on contact material b gold q silver g gold over silver p gold, matte-tin s silver, matte-tin r gold over silver, matte-tin seal e epoxy f epoxy seal and splashproof r tv la tex rubber seal terminations a right angle, pc thru-hole (ts01 & ts03 models only) c pc thru-hole w wire wrap models available
i slide iC dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com ts series tiny slide switches switch function termina tions actuator shown in pos. 1 pc mounting pc mo unting ts02 models: omit center hole spdt spst 2-3 3-1 open n/a 1-2 open on none on on off on off none on ts01 ts03 ts02 sp schematic connected terminals pos. 1 pos. 2 pos. 3 switch function pos. 1 pos. 2 pos. 3 model no. no. poles terminal nos. for refer ence only ts02 models: omit center terminal spdt part number shown: ts01cbe c&k marking on opposite side c&k marking on opposite side w wire wrap c pc thru-hole a right angle, pc thru-hole all models with all options when or dered with g, q, r or s contact material. ts02 model not available with a terminations. spdt and spst not available with ts02 model. spdt and spst TS01ABe horizontal actuation spdt
iC0 dimensions are shown: inch (mm) specifications and dimensions subject to change www.ck-components.com i slide ts series tiny slide switches contact material seal f epoxy seal and splashproof r tv latex rubber seal e epoxy seal note: rtv latex rubber seal peels off easily after installation. epoxy terminal seal standard. not available with a termination. * note: see technical data section of this catalog for rohs compliant and compatible definitions and specifications. 1 cont acts & terminals: copper alloy, with gold plate over nickel plate. 2 end contacts: coin silver, with gold plate over nickel plate. 3 center contacts & all terminals: copper alloy, with gold plate over nickel plate. 4 end cont acts: coin silver, silver plated. 5 center cont act & all terminals: copper alloy , silver plated. 6 terminals: copper alloy , with matte-tin over nickel plate all models with all options when ordered with g, s or r contact material. b contact material standar d with a and w terminations. q contact material standard with c terminations. note: any models supplied with q, b, g, p , s or r contact material are rohs compliant. ts01 models: 0.4 v a max @20 v ac or dc max. or 3 amps @ 120 v ac or 28 v dc. ts02, ts03 models: 0.4 va max @ 20 v ac or dc max. or 1 amp @ 120 v ac or 28 v dc. ts01 models: 3 amps @ 120 v ac or 28 v dc. ts02, ts03 models: 1 amp @ 120 v ac or 28 v dc. 0.4 v a max. @ 20 v ac or dc max. low level/dry circuit or power power low level/dry circuit gold over silver 2,3 sil ver 4,5 gold 1 option code ra tings contact material b p q s g r gold 3 matte-tin 6 silver 5 ma tte-tin 6 gold 3 matte-tin 6 terminal pla ting
|
